4.8L / 4L60E - transmission clearance issues

Anything to do with the LS1 and the variants.

Moderators: Super Mod, Moderators

4.8L / 4L60E - transmission clearance issues

Postby projected » Tue Nov 21, 2017 4:31 pm

Currently trying to drop a 4.8 / 4L60E combo into a 98 Sonoma - I notched the frame and I'm using a "weld it yourself" set of eBay mounts that look identical to those sold by trans-dapt.

I can not get the engine back far enough against the firewall to clear the notch as the transmission is hitting the transmission tunnel. I pulled he intake to get more clearance but it's still not enough. Do I need to jack the truck higher and install the engine at an extreme angle and pivot it back into place? Is it common to have to modify the tunnel on these swaps? I can cut the notch deeper but it looks nearly identical to the picture shown below.

Image


To further complicate things, I unexpectedly acquired a much nicer '03 S10 in an identical configuration - this power train is going to be moved to it as soon as I figure out the issue with the Sonoma (Sonoma is getting junked, frame is rough).
projected
I found rocker arm monkey's on ebay!
 
Posts: 1
Joined: Tue Nov 21, 2017 4:20 pm

Re: 4.8L / 4L60E - transmission clearance issues

Postby Rickracer » Wed Nov 22, 2017 5:44 am

We typically fold back the lip between the firewall and the floor, it helps even on stock V6 trucks. :wink: 8)
Rickracer
ASE Certified Master Automotive Technician (well over 3 decades of experience, :thumbup: )
'93 S10 SB,RC, Comp XR276 Hydraulic Roller, Vortec head 363, 400 + hp, built 700R4, JW 2800 stall lockup converter, 3.73 posi, disc brake, narrowed 8.8 Exploder rear, LS Camaro front discs, Cal-Trac clone traction bars, Best N/A passes to date: 7.76 in the 1/8th, 12.24@109.27 mph in the 1/4, gonna spray it one of these days... :mrgreen:
76 Chevy Vega Drag Car, TWIN TURBO 355, P/G trans w/ brake and JW 4000 stall vert, 4 link back half, narrowed 9", 3.50 gears, 29.5x10.5W ET Drags. Best time9.669 @ 139.79, Latest video: https://www.youtube.com/watch?v=S59riYn ... ata_player
Rickracer
Master Swap Tech
Master Swap Tech
 
Posts: 28913
Joined: Wed Apr 26, 2006 8:02 am
Location: Kissimmee, Fl.

Re: 4.8L / 4L60E - transmission clearance issues

Postby jayyk31 » Tue Nov 28, 2017 6:56 pm

What oil pan are u using? That notch looks big enough for most pans you should have no clearance issues. Other than what rick suggested, lift the cab up off the frame and slide the engine and trans in.
jayyk31
WHERES THE CAPS LOCK?
 
Posts: 138
Joined: Thu Nov 27, 2014 6:13 am

Re: 4.8L / 4L60E - transmission clearance issues

Postby XLR8R » Thu Nov 30, 2017 11:09 pm

Projected; Are you trying to drop the motor and trans in at the same time? If so, I can tell ya now it will not work that way in any S10 that I know of without severe cutting/beating. Trans or motor must be installed before the other then attached from underneath. Your 4L60E should bolt in easily as this is the native trans for this truck. I would get it in first, then drive shaft to make sure it's all in right place, then motor.
Hope this helps
XLR8R
I found rocker arm monkey's on ebay!
 
Posts: 1
Joined: Thu Nov 30, 2017 10:56 pm


Return to LSx Tech

Who is online

Users browsing this forum: No registered users and 1 guest