Oil pan ????

Anything to do with the LS1 and the variants.

Moderators: Super Mod, Moderators

Oil pan ????

Postby wkeracing » Thu May 11, 2017 7:16 pm

Anybody running the holley oil pan 302-1 ?? any pics of the clearances ??
Make sure you get your information from the internet gurus that haven't built ****, they did sleep at Holiday Inn last night.
User avatar
wkeracing
Im working on unhooking my battery cables.
 
Posts: 72
Joined: Fri Jul 22, 2016 6:33 pm
Location: Lafayette, Louisiana

Re: Oil pan ????

Postby XXXXXXXX » Fri May 12, 2017 2:04 am

Sorry not me.. bone stock 305.. I take it your doing an LS swap?

There are some not so great dimensions here. https://www.summitracing.com/parts/hly-302-1

X
82 S10 Longbed.. stock 305.. b&m 144 blower.. 7lbs.. stock 801 heads.. dyno'd 194rwhp...holley 750dp.. percys adjust a jet in the front & rear.. headman 1 1/2 shorty headers.. 2 1/4 dual exhaust with hooker aero chambers.. msd with boost timing master.. 2500 stall .. 700r4 .. 3.73 posi fact s10 disc brake rear end.. caltracs.. 275/60/15 Nitto Extreme 555 drag radials
XXXXXXXX
I drink used anti-freeze
 
Posts: 768
Joined: Wed Aug 05, 2015 9:35 pm

Re: Oil pan ????

Postby gsjimmy » Wed Jun 07, 2017 7:47 am

Running a LH8 GM pan. Had to clearance the x-member about an inch (cab side) to fully engage the motor mounts. The Holley pan looks very similar to the LH8.

Cut-off wheel and a welder will get the job done. Finished result is not real noticeable to most folks
gsjimmy
I just gutted everything.
 
Posts: 92
Joined: Sat Dec 11, 2004 8:19 pm

Re: Oil pan ????

Postby patl » Sat Jul 01, 2017 3:28 pm

Muscle car pan works from jegs. Includes everything pickup, dipstick and bolts for bout 200 bucks...
bone stock 200k mile 5.3 best et 7.96 8th mile (only pass on the brake) with a 1.56 60..
User avatar
patl
I found rocker arm monkey's on ebay!
 
Posts: 6
Joined: Tue Nov 15, 2016 8:02 pm
Location: SE NC

Re: Oil pan ????

Postby wkeracing » Wed Jul 05, 2017 8:01 am

I don't want to use the LH8, H3 or muscle car pan because they hang below the crossmember. Was asking about the holley pans, but have found out the info i was looking for.
Make sure you get your information from the internet gurus that haven't built ****, they did sleep at Holiday Inn last night.
User avatar
wkeracing
Im working on unhooking my battery cables.
 
Posts: 72
Joined: Fri Jul 22, 2016 6:33 pm
Location: Lafayette, Louisiana

Re: Oil pan ????

Postby gsjimmy » Wed Jul 12, 2017 7:16 am

Only hangs down about 1/2 to 3/4 inch. Unless the truck has been really lowered, isn't a problem. Mine is a ZQ8 and sits lower than a stock S10. Can always add a small skid plate.

03 S10 Ext Cab
1999 5.3 GEN III - LS1 cam, cold air intake, CPP poly mounts

"Work in progress"
gsjimmy
I just gutted everything.
 
Posts: 92
Joined: Sat Dec 11, 2004 8:19 pm


Return to LSx Tech

Who is online

Users browsing this forum: No registered users and 2 guests