Oil pan ????

Anything to do with the LS1 and the variants.

Moderators: Super Mod, Moderators

Oil pan ????

Postby wkeracing » Thu May 11, 2017 7:16 pm

Anybody running the holley oil pan 302-1 ?? any pics of the clearances ??
Make sure you get your information from the internet gurus that haven't built ****, they did sleep at Holiday Inn last night.
User avatar
wkeracing
Im working on unhooking my battery cables.
 
Posts: 71
Joined: Fri Jul 22, 2016 6:33 pm
Location: Lafayette, Louisiana

Re: Oil pan ????

Postby XXXXXXXX » Fri May 12, 2017 2:04 am

Sorry not me.. bone stock 305.. I take it your doing an LS swap?

There are some not so great dimensions here. https://www.summitracing.com/parts/hly-302-1

X
82 S10 Longbed.. stock 305.. b&m 144 blower.. 7lbs.. stock 801 heads.. dyno'd 194rwhp...holley 750dp.. percys adjust a jet in the front & rear.. headman 1 1/2 shorty headers.. 2 1/4 dual exhaust with hooker aero chambers.. msd with boost timing master.. 2500 stall .. 700r4 .. 3.73 posi fact s10 disc brake rear end.. caltracs.. 275/60/15 Nitto Extreme 555 drag radials
XXXXXXXX
I drink used anti-freeze
 
Posts: 730
Joined: Wed Aug 05, 2015 9:35 pm

Re: Oil pan ????

Postby gsjimmy » Wed Jun 07, 2017 7:47 am

Running a LH8 GM pan. Had to clearance the x-member about an inch (cab side) to fully engage the motor mounts. The Holley pan looks very similar to the LH8.

Cut-off wheel and a welder will get the job done. Finished result is not real noticeable to most folks
gsjimmy
I just gutted everything.
 
Posts: 92
Joined: Sat Dec 11, 2004 8:19 pm

Re: Oil pan ????

Postby patl » Sat Jul 01, 2017 3:28 pm

Muscle car pan works from jegs. Includes everything pickup, dipstick and bolts for bout 200 bucks...
bone stock 200k mile 5.3 best et 7.96 (only pass on the brake) with a 1.56 60..
User avatar
patl
I found rocker arm monkey's on ebay!
 
Posts: 5
Joined: Tue Nov 15, 2016 8:02 pm
Location: SE NC

Re: Oil pan ????

Postby wkeracing » Wed Jul 05, 2017 8:01 am

I don't want to use the LH8, H3 or muscle car pan because they hang below the crossmember. Was asking about the holley pans, but have found out the info i was looking for.
Make sure you get your information from the internet gurus that haven't built ****, they did sleep at Holiday Inn last night.
User avatar
wkeracing
Im working on unhooking my battery cables.
 
Posts: 71
Joined: Fri Jul 22, 2016 6:33 pm
Location: Lafayette, Louisiana

Re: Oil pan ????

Postby gsjimmy » Wed Jul 12, 2017 7:16 am

Only hangs down about 1/2 to 3/4 inch. Unless the truck has been really lowered, isn't a problem. Mine is a ZQ8 and sits lower than a stock S10. Can always add a small skid plate.

03 S10 Ext Cab
1999 5.3 GEN III - LS1 cam, cold air intake, CPP poly mounts

"Work in progress"
gsjimmy
I just gutted everything.
 
Posts: 92
Joined: Sat Dec 11, 2004 8:19 pm


Return to LSx Tech

Who is online

Users browsing this forum: No registered users and 2 guests